3D2A Printing Guide

3D2A Printing Guide

Nov 18, 2026
30

(For PPA, PA, and PAHT Nylons)

  • Filament:

    Dry your Filament at 85c for 24 hours (PPA is best at 100-140c for 24 hours), rotate or flip your spool halfway through to ensure even drying. Most off-the-shelve filament dryers range from 65c to 85c, I use the Creality SpacePi X4, but many others will work and are better. For PPA I run mine for 24 hours at 85c, then 12hours at 120c on my X2d's bed, flipping it halfway through. Some people use food dehydrateors or electric ovens (Both with thermistors not thermocouples). I have not tried those methods after seeing pictures of $100+ spools being ruined due to poor temperature regulation, so I will not recommend it. I have used PA6-CF, PA6-GF, PPA-CF, PPA-GF, and PAHT-CF with ranging fiber contents from Bambu, Polymaker (Fiberon), Sunlu, and Sirayatech. I have had good experiences with all 4 brands, however I recommend Polymakers Fiberon out of the 4. My order from best to worst is PPA, PA, and PAHT. I prefer CF over GF, as CF tends to have better tensile strength. I suggest Fiberon PA6-CF20 as it has the most balanced performance and best bang for your buck to make cans with in my opinion.

    • Hardware:

      You need an enclosed printer with a bed temp off min 100c, a nozzle of min 300c, and preferably a chamber heater, though it is not required. You will also need at minimum a hardened nozzle, a tungsten nozzle is preferred and is the strongest Bambu offers. However, a diamond or ruby nozzle will last longer than the printer. I use a .4mm Tungsten Highflow nozzle on both my Nylon dedicated printers and re-slice the 3mf files for a standard .4mm nozzle. I use .4mm for better detail on the prints, and it is the most common size. A .6mm is recommended for Fiber-infused Nylons due to clogging potential. I have only experienced clogging (outside of my stupid mistakes) after printing low-temp filaments, and then switching to high-temp filaments. The nozzles I use for Fiber Nylons are only for Fiber Nylons due to that fact. I also use the Bambu engineering plate, a textured or smooth PEI plate works as well. I just prefer no texture. Always use glue on build plate with any nylon or any bed plate, it helps with bed adhesion.

    • Printing:

      All Nylons need to be printed hot and slow for best layer adhesion (Yes more than recommended at times). The nozzle temps should be at around 300c for PA6 and PAHT. If your printer allows it up to 340c for PPA. Make sure you are using my print profile labeled ".15mm PA6-CF" and my updated filament profile labeled "PA6-CF High Temp", It is for all three nylons listed. I am still adding it to some of my older models. If you see one without it, shoot me a message and I will fix it. Do not increase print speed. If you have a heated chamber, set it to 60-65c. If you do not, heat soak your printer by setting your build plate to max temp for 30mins prior to printing. Bambu has a setting that automatically turns bed temp to 0c while not printing after 10 mins (I disabled this).

  • Post processing:

I do not personally anneal my prints, I have had great experiences and have gotten over 4k rounds on the FTN.5 Flow model and over 1400 rounds out of the FTN.5 300 Blackout model (With subs) without doing so. You can if you wish, but I do not have any recommendations for it. You do want to moisture condition all Fiber Nylon prints after printing, especially PA6CF. It soaks up water like a sponge. There are different methods of introducing moisture. You can leave it in a moist environment. If you live in the south like me, put it outside (40% hummidity most days), put it in a ziplock bag with a damp sponge. I saw a post where someone put theirs in the fridge (Don't do that lol). I just soak mine in water for a couple hours and then set them outside to air dry for a day(When its warm). You can set it in front of a fan after for a couple hours, or just leave it out in the house for a day or 2 (Shake out all the water first). When Nylons are dry they are extremly brittle, with the lower pressure models (22lr and 9mm) it is fine. With rifle caliber cans they will crack inside the sleeve the first 20 shots. That is why you want to introduce some moisture back into the print. I epoxy all my thread adapters in with JB-weld. With rimfire cans and some 9mm pcc cans it is not required, if you try it with 9mm Boosterless or rifle caliber, it will shoot the can off the threads eventually. Also spray water inside or submerge can to cool down inbetween mags if shooting large volumes, it will significantly increase the cans lifespan. Alternativly if you have multiple of the same can, rotate them out.

  • Most Common Problems:

    Using wet filament, using the wrong filament, not using glue on build plate, using the wrong-sized nozzle, putting the wrong can on the wrong pew or wrong caliber, changing or not using my filament or print profile, not moisture conditioning print, not epoxying the adapter in, using an open printer (Bed slinger) to try to print Fiber Nylons.

  • Legality and Safety

I am no lawyer. Check your local, state, and federal laws where you live. Where I live everything I make is legal the way I make it. In your state, city, or country it may not be. I am not responsible for what you make or where you make it. You should also assume the risk of putting something plastic on the end of your gun, prepare appropriately (ie. Saftey glasses or shooting a lesser caliber out of the can first in the case of anything besides 22lr). Use a bore rod before firing to ensure can alingment and inspect for any deformities that may cause a failure (ie. Layer shifts, signs of wet filament, under extrusion, ect.). This is all from my personal experience and there may be better ways to do certain things. I am nearing 20 kilos of PA6CF alone and on my 9th of PPACF with over 90 individual cans completed (I have lost count at this point) These are the things I have learned or my preferences, they are not law. They will put you on the right path, but I encourage everyone to do their own research.

  • My Kit for Fiber Nylons:

  • Bambu P2S with aftermarket chamber heater

  • Bambu X2D

  • .4mm Tungsten high flow nozzles for both

  • Engineering build plate for both

  • Creality SpacePi X4 Filament dryer

    Thank you for every like, comment, review, boost, follow, and donation. It helps me to keep testing and uploading models. Your support does not go unnoticed and is greatly appreciated.

    If you have any custom requests or specific designs on a specific model you want. This is my Signal Username: PrintedNLoaded.90

    For any longer conversations or to keep things without extra ears message me there.

Подобається цей допис?

Купити для PrintedNLoaded пиво

КонфіденційністьУмови